 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Spindle Position Displays Hollow shaft max. o25 mm, manual format alignment Display LCD two lines, interface RS485 N 140 Features - Electronic spindle position display - Absolute multiturn measuring system - Display: LCD backlit, two lines - Actual value and target display - Hollow shaft o20 mm / o25 mm - Interface RS485 - Resolution: 2304 steps/revolution 4096 revolutions N 140 with cable output Technical data - electrical ratings Voltage supply Current consumption Display Measuring principle Measuring range Steps per turn Number of turns Spindle pitch Interface Data memory 24 VDC 10 % 30 mA LCD, 7-segment display, 2-lines, backlit Absolute multiturn measuring system -999,99...+9999,99 mm -99.999...+999.999 inch 2304 4096 / 12 bit 23 mm RS485 (ASCII protocol) Parameter buffer: EEPROM Current value buffer: >10 years by integrated 3 V lithium battery Display position horizontal/ vertical Measuring unit mm/inch Counting direction Spindle pitch Spindle tolerance Positioning direction Direction arrows Tolerance window Round up/down Protection class II Overvoltage category II Pollution degree 2 DIN EN 61000-6-3 DIN EN 61000-6-2 UL/cUL Housing type Dimensions W x H x L Mounting Weight approx. Material Technical data - mechanical design Hollow shaft Operating speed Protection DIN EN 60529 Operating temperature Storing temperature Relative humidity Torque support E-connection o20 mm, o25 mm 600 rpm (short-term) IP 65 -10...+50 C -20...+70 C 80 % non-condensing Torque pin provided at housing - Cable output (30 cm) with male/female connector M16, 5-pin Surface-mount with hollow shaft 56 x 100 x 62.5 mm Surface-mount with hollow shaft Polycarbonate black, UL 94V-0 Subject to modification in technic and design. Errors and omissions excepted. 30/10/2008 200 g Programmable parameters Standard DIN EN 61010-1 Emitted interference Interference immunity Approval 1 www.baumerivo.com Hollow shaft max. o25 mm, manual format alignment Display LCD two lines, interface RS485 Spindle Position Displays N 140 Part number N 140. 1 0 3 A 01 Hollow shaft A Hollow shaft o25 mm B Hollow shaft o20 mm Display A Inclined Voltage supply 3 24 VDC E-connection 0 Cable output with M16 connector Interface 1 RS485 Accessories Connectors and cables (page %S) Z 165.B01 Z 165.AW1 Z 165.D05 Z 165.S01 Z 165.V01 Mating connector M16, 5-pin, less cable Cable connector M16, 5-pin, less cable with integrated terminating resistor 120 Data and supply cable M16, Master to N 140, N 141 and N 142, 5 m Cable connector M16, 5-pin, less cable Coupling cable between M16 and M16, 1 m Description N 140 spindle position display supports the editing engineer in manual spindle positioning operations. The principal benefits of the new electronic spindle position display is saving time in machine setup and editing as well as elimination of errors when aligning formats to new position values. The absolute measuring system captures any change in position even in powerless state. The backlit LCD display provides the editing engineer with all necessary information for efficient editing of new spindle positions. The two-line display shows both current value and target. A little arrow signalizes the editing engineer the direction the spindle must be turned to get to the new position. RS485 serial interface enables network of 32 spindle position displays with PC or PLC. For complete solutions also memory controllers as decentralized operating and memory terminals are available. Up to 100 format profiles can be stored by teach-in. Upon request the desired profile is recalled and retransmitted upon pressing a button to every spindle position and shown as target. 2 www.baumerivo.com 30/10/2008 Subject to modification in technic and design. Errors and omissions excepted. Spindle Position Displays Hollow shaft max. o25 mm, manual format alignment Display LCD two lines, interface RS485 N 140 Terminal assignment Connector Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Assignment Sensor supply +24 V Sensor supply 0 V - Tx/Rx+, RS485 Tx/Rx-, RS485 M16 connector 4 5 3 2 1 1 5 2 3 4 M16 female connector Dimensions Hollow shaft O25 mm 7 Fixing pin for bore O10 mm 58.5 40 0.2 Hollow shaft O20 mm 100 25 H7 7) (20 H O37 M5 O37 M5 4 Subject to modification in technic and design. Errors and omissions excepted. 30/10/2008 8 20 6 10 1 62.5 21.5 8.5 16 56 M16-female connector M16 connector 3 www.baumerivo.com O37 Hollow shaft max. o25 mm, manual format alignment Display LCD two lines, interface RS485 Spindle Position Displays N 140 4 www.baumerivo.com 30/10/2008 Subject to modification in technic and design. Errors and omissions excepted. |
Price & Availability of N140103AA
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |